The following prose is extracted from the k12mit.doc file, which consists mostly of update history, but which should nevertheless be considered the authorative documentation.
AS OF THE CURRENT IMPLEMENTATION, THE FOLLOWING COMMANDS ARE EFFECTIVE:
FILESPEC MAY BE ANY LOCAL (OS/8) FILE-STRUCTURED DEVICE:FILENAME.EXTENSION, WHERE THE FILENAME AND EXTENSION WILL BE TRUNCATED TO 6 ALPHANUMERICS AND 2 ALPHANUMERICS RESPECTIVELY, AS NECESSARY (THIS IS REFERRED TO AS 6.2 FILENAME FORMAT). THE DEVICE: FIELD IS OPTIONAL; ALL COMMANDS USING THE DEVICE: FIELD FOR LOCAL DEVICE SPECIFICATION WILL USE THIS DEVICE AS THE SOURCE OR DESTINATION AS NECESSARY FOR THE LOCAL FILES. IF THE DEVICE: FIELD IS OMITTED, THE DEFAULT DEVICE DSK: WILL BE USED. THE ACTUAL DEVICE USED MAY BE SELECTED BEFORE INVOKING KERMIT-12 BY USING THE OS/8 ASSIGN COMMAND:
.ASSIGN DEV DSK
WHERE DEV IS ANY AVAILABLE FILE-STRUCTURED DEVICE.
KERMIT-12 USES AN UNUSUAL SCHEME FOR ITS PROMPT: THE ACTUAL DEFAULT PROMPT TEXT IS PARTIALLY TAKEN FROM THE ACTUAL MACHINE KERMIT-12 IS CURRENTLY EXECUTING ON. FOR EXAMPLE, IF KERMIT-12 HAS DETERMINED THE CPU TYPE AS PDP-8/E, THE PROMPT WILL BE:
KERMIT-8/E>
THIS ALLOWS KERMIT-12 USERS (WITH DIFFERENT CPU-TYPE MACHINES) TO DISTINGUISH MESSAGES ORIGINATING FROM THE RESPECTIVE SYSTEMS. FUTURE VERSIONS WILL SUPPORT USER PROMPT STRINGS TO ALLOW MORE DISTINCTIVE SYSTEM MESSAGES.
THE HELP OR CONNECT COMMANDS MAY BE USED TO DETERMINE THE CURRENT CONNECT MODE ESCAPE CHARACTER.
THE RECEIVE COMMAND ALLOWS OPTIONAL DEVICE: ONLY. THE FILENAME AND EXTENSION ARE NOT ALLOWED. NAMES OF RECEIVED FILES WILL BE MODIFIED IF NECESSARY TO CONFORM TO THE 6.2 FORMAT. IMPLEMENTATION RESTRICTION: CERTAIN REMOTE FILENAMES CONTAINING NON-ALPHANUMERIC CHARACTERS MAY CAUSE KERMIT-12 TO HASTILY ABORT THE TRANSMISSION AND RETURN TO COMMAND LEVEL.
THE GET COMMAND ALLOWS OPTIONAL DEVICE: TO DETERMINE DESTINATION OF THE INCOMING FILES. THE OUTBOUND FILESPEC MUST CONFORM TO LOCAL CONVENTIONS (FILENAME AND EXTENSION ARE NOT LIMITED TO 6.2 FORMAT; THE DEVICE: FIELD WILL NOT BE SENT TO THE REMOTE KERMIT UNLESS IT IS ILLEGAL WITHIN OS/8 SPECIFICATIONS, SUCH AS TOO MANY DEVICE LETTERS. IN THIS CASE, THE DEFAULT DEVICE DSK: APPLIES, AND THE ENTIRE "DEVICE" FIELD IS SENT ALONG WITH ANY FILENAME AND EXTENSION). CERTAIN REMOTE SYSTEMS ARE INCOMPATIBLE WITH THIS IMPLEMENTATION, AS IMBEDDED SPACES OR NON-ALPHANUMERIC CHARACTERS ARE NOT ALLOWED, EVEN THOUGH THEY MAY BE REQUIRED ON THE REMOTE SYSTEM. WILD-CARD CHARACTERS ARE ALLOWED, BUT ONLY AS SPECIFIED IN THE SEND COMMAND ABOVE.
CTRL-X OR CTRL-Z CAN BE USED TO ABORT KERMIT TRANSMISSIONS (EVENTUALLY) BUT IS NORMALLY A SLOW PROCESS, SINCE THE CHECKING IS DONE BY A SOFTWARE TIMEOUT SCHEME. AT THE PRESENT TIME, THERE IS NO DISTINCTION BETWEEN THESE THO CHARACTERS, SO IT IS NOT POSSIBLE TO ABORT A SINGLE FILE; THE ENTIRE BATCH OF FILES INVOLVED IN THE TRANSFER IS ABORTED.
CONNECT MODE RUNS IN 8-BIT MODE.
THE COMPOSE KEY IS ENABLED FOR USE WITH A LOADED COMPOSE TABLE.
ANY VALID DECMATE II/III/III-PLUS CHARACTER SET IS ALLOWED WHILE IN CONNECT MODE (MCS TCS LINE, ETC.). ALL ESCAPE SEQUENCES ARE PASSED TO THE SLUSHWARE/FIRMWARE UNMODIFIED.
KEYBOARD UPPER-CASE LOCK WILL ALWAYS BE AUTOMATICALLY APPLIED UPON RETURN FROM CONNECT MODE.
[ PDP-8 Kermit ] [ Kermit Project Home ]