[email protected]
The following method has been written for use with the Slackware Linux distribution. It assumes some familiarity with it's installation. The installer will also need access to a working Linux system of any distribution. It also assumes the destination system has 4 to 6 megs ram. More powerful systems can use this method also but you will probably be able to find a faster easier way. It is not intended to be used by first time installers or by people new to Linux. Only issues specific to the use of a zip drive as source media will be covered here.
I have an OLD 486/20 slc with a 120 meg hd, 4 megs ram and a 2400 baud modem that I wanted to run Linux on. It has no cdrom drive or pcmcia connectivity, and will never see a network card (parallel port style). There is nothing left that can be upgraded on this unit.
Linux has been at the cutting edge from the start but also breathes new life into some older 386 and 486 hardware. The documentation says "386 with 2 megs ram no math coprocessor" but try to find a distribution that will do it today. Slackware can be placed on a 4 meg machine with some work and a prayer. The following system greatly reduces the work. Prayer always helps, even with the best of systems.
I've used the following system with 3 other laptops, and one 386 desktop machine. The lamest being a 386 with 4 megs ram & 60 meg HD no math coprocessor. While this system works well I'd like to be able to do similar tricks with Debian, RedHat, Caldera Lite, and some of the other popular distributions offering more choice to Linux users I help this way.
Installing from cdrom or Ethernet are the methods of choice when available. In cases where floppy disk install appears to be the only choice a parallel port zip drive offers numerous advantages. These include better speed than a floppy disk, and fewer disk changes. In addition on systems with minimal ram "6 megs. or less" the ability to install a swap file on the root disk uncomplicates the install greatly by freeing you from the need to creat one on the hard disk before running setup. When installing Slackware the swap file allows installers to choose the color.gz root disk or text.gz. The color.gz is not recommended for floppy based installs on machines with such limited resources. With a zip disk you may also produce an emergency boot disk during the initial install, by freeing the first floppy drive. Something not possible during a normal floppy based install on systems of this type.
This method has been used with Slackware Ver's. 3.1, through 3.4 A full Slackware install requires 2 zip disk's not counting source packages if they are desired. You will need one parallel port zip drive & cables, and a 1.44 meg boot disk. Pencil and paper are optional for making a few notes during install.
At least two systems are required to use this install method. The first (host) system is used to prepare the installation media and must contain a working Linux system. The second will be the target system. Once the media has been prepared it can be used to install to as many target systems as you like. I work from cdrom but you can down load your distribution from the Internet if you have a fast enough connection. For me this is not practical.
let (floppy) represent the path to and directory you
mount your 1.44 meg floppy disk on.
let (zip) represent the path to and directory you
mount your zip disk on.
let (cdrom) represent the path to and directory you
mount your cdrom on.
let (verx.x) represent the distribution version you
are installing.
If you down load your disk images please let (cdrom)/slakware the path and directory to those images. My parallel port zip drive shows up on my system as
/dev/sda4
/dev/hdc cdrom
/dev/fd0 1.44 meg floppy
About Slackware and slakware (note the missing c in slakware). Slackware is the name of the overall distribution and slakware is the name of the directory where Patrick Volkerding places the stable "not experimental or developmental" packages for installation. Whenever I'm writing about slakware I'm writing about the directory.
Linux Installation and Getting Started by Matt Welsh
If you are having trouble accessing your zip drive please see the
Linux
ZIP drive mini-HOWTO by Grant Guenther
When you have completed your install I can not recommend strongly
enough that you work through the
Small-Memory mini-HOWTO by Todd Burgess
I also recommend the LOWMEM.TXT document from the Slackware documentation on your cdrom or Slackware ftp site. This document discribes a system that eleminates many of the difficulties discribed in that document.
1) Attach zip drive to host system, insert blank zip disk into the drive and boot the system to Linux
2) Login. You probably need to login as root or the user you log in as will need to be able to write file systems, mount and unmount disks etc....
3) Install an ext2fs file system on the zip disk. with the command:
/sbin/mke2fs -b 1024 /dev/sda4
mount /dev/sda4 /(zip)
mount /dev/hdc /(cdrom)
mkdir /(zip)/slakware
mkdir /root/slakware/(verx.x)
cp /(cdrom)/rootdsks/text.gz /root/slakware/(verx.x)/
cd /root/slakware/(verx.x)
gunzip text.gz
dd if=text of=/dev/fd0
mount /dev/fd0 /(floppy)
cp -dpR /(floppy)/* /(zip)/
dd if=/dev/zero of=/(zip)/swap bs=1024 count=8208
/sbin/mkswap /(zip)/swap 8208
/sbin/swapon /swap
cp -r /(cdrom)/slakware/[a-ty]* /(zip)/slakware/ &
17) External zip drives have two lights--mine are green and yellow; the internal drives appear to have only one. When my zip disk has finished receiving information the yellow light goes out and I'm left with just the green power light. on internal drives the single "status?" light will go out.
It is now time to prepare the floppy and zip disks for removal from their drives by unmounting them:
cd
umount /dev/fd0
umount /dev/sda4
18) Life will be easier later if we check the root disk's file system before we try to use it with the command:
/sbin/e2fsck -f /dev/sda4
When disk activity ends if there are no errors you may remove the zip disk from the drive and label it Slackware Root disk. I also include the version number in pencil.
If the X window system is to be installed or you will be needing one of the other prebuilt kernels it is now time to build the 2nd. zip disk.
x1) Insert disk 2 in the zip drive. I like to write an ext2fs file system on this disk also, but if it has a M$ Dos file system that will work also. I use the up arrow key on my keyboard to recall previously used commands from my history file because I'm a bit lazy, but if you want to retype the command repeat instructions 3), 4), and 6) above.
x2) Copy the X11R6 "X Window" packages to zip
cp -r /(cdrom)/slakware/x* /(zip)/slakware/ &
x3) There is also room on this disk for the custom kernels directory. It is classy to install one that meets the system's needs as closely as possible to go with the one needed to access the zip drive. Make this kernel the system default. So now we will make a directory for that and then copy the information to it:
mkdir /(zip)/kernels
cp -r /(cdrom)/kernels/* /(zip)/kernels/ &
x4) When disk activity is at an end unmount the disk and run fsck on it:
umount /dev/sda4
/sbin/e2fsck -f /dev/sda4
b1) I now make a 1.44 meg boot disk. Use the /(cdrom)/bootdsks.144/iomega.s image. Install a new 1.44 meg floppy disk in the proper drive. The command to make the disk is:
dd if=/(cdrom)/bootdsks.144/iomega.s of=/dev/fd0
b2) Check the file systems of the boot disk:
/sbin/e2fsck -f /dev/fd0
After connecting everything up to the target machine and putting the zip disk in place I boot the machine with the appropriate boot disk. Before logging in it is a good idea to use the scroll back feature built into Linux and check to see all your hardware was detected properly. To do this hold the shift key and use the page up and page down keys as appropriate. Getting a login prompt at all usually means the boot time errors were not too bad.
Slackware will present some instructions. Please read them Carefully. Login as root and fdisk root and swap partitions on the target drive if needed. Reboot the machine if you ran fdisk and Carefully reread the instructions on the screen if there are any, then login as root.
Even on machines with only 4 megs. of ram you will not need to create a swap partition until prompted to do so in the setup program. We already have swap running on the zip disk. Run the Slackware setup program:
setup
You do not want to allow /dev/sda4 to be automatically mounted and when questions come up about this in the menus. Do not add it unless this zip drive is dedicated to the target machine full time.
When you get the menu that asks where the source of the installation media is select item number 4. "Install from a premounted directory". The next screen will ask for its name, it is /slakware.
I recommend installing only the "a" disk set at this time. It will crash the install if the person selecting packages gets greedy and fills the disk before lilo is written and the kernel is installed. During basic install I install the kernel from the boot disk only. There are relatively few choices to be made from here and the Slackware documentation from the cdrom or your ftp site will do you much better than I can from here.
Leave the zip drive and disk in place after the initial install is complete. Remove the floppy when prompted to do so and reboot. If all is right in the world Bill, er, your friend/customer will have a working Linux system come up.
After rebooting the system login as root and mount the zip disk again:
mount /dev/sda4 /mnt
df
setup
Enter the directory name. This time use:
/mnt/slakware
umount /dev/sda4
You may now remove the disk and if X will be installed insert the 2nd zip disk and work through setup again this time only packages beginning with X will be available. If you will be installing a custom kernel from the prebuilt kernels you may also do this while the 2nd. zip disk is installed.
Some times I have trouble with the links for the libraries either on the root zip disk or on the final destination machine. There are two possible fixes for this.
Fix 1) If the system boots to a command prompt and you can login as root in single user mode try the command:
ldconfig
Fix 2) If ldconfig can not repair things you will need to re master the root floppy disk and recopy the files from it as in instruction 8) through 12) or reinstall Linux to the destination system as appropriate.
This mini-HOWTO brought to you by the letters G. N. and U. and the Linux documentation project.
Special thanks to Dr. Randolph Bentson whose devotion to Linux inspired me to give something back to the people who gave us the ONE TRUE OPERATING SYSTEM.
I hope this helps someone.
Sincerely
Kevin Snively
P.O. Box 1013
Everett Wa. 98206-1013
USA
root@aldrovanda