1.1. Legal stuff

Copyright (c) <2002> by Tavis Barr, Nicolai Langfeldt, Seth Vidal, and Tom McNeal. This material may be distributed only subject to the terms and conditions set forth in the Open Publication License, v1.0 or later (the latest version is presently available at http://www.opencontent.org/openpub/).

1.2. Disclaimer

This document is provided without any guarantees, including merchantability or fitness for a particular use. The maintainers cannot be responsible if following instructions in this document leads to damaged equipment or data, angry neighbors, strange habits, divorce, or any other calamity.

1.3. Feedback

This will never be a finished document; we welcome feedback about how it can be improved. As of February 2002, the Linux NFS home page is being hosted at http://nfs.sourceforge.net. Check there for mailing lists, bug fixes, and updates, and also to verify who currently maintains this document.

1.4. Translation

If you are able to translate this document into another language, we would be grateful and we will also do our best to assist you. Please notify the maintainers.

1.5. Dedication

NFS on Linux was made possible by a collaborative effort of many people, but a few stand out for special recognition. The original version was developed by Olaf Kirch and Alan Cox. The version 3 server code was solidified by Neil Brown, based on work from Saadia Khan, James Yarbrough, Allen Morris, H.J. Lu, and others (including himself). The client code was written by Olaf Kirch and updated by Trond Myklebust. The version 4 lock manager was developed by Saadia Khan. Dave Higgen and H.J. Lu both have undertaken the thankless job of extensive maintenance and bug fixes to get the code to actually work the way it was supposed to. H.J. has also done extensive development of the nfs-utils package. Of course this dedication is leaving many people out.

The original version of this document was developed by Nicolai Langfeldt. It was heavily rewritten in 2000 by Tavis Barr and Seth Vidal to reflect substantial changes in the workings of NFS for Linux developed between the 2.0 and 2.4 kernels. It was edited again in February 2002, when Tom McNeal made substantial additions to the performance section. Thomas Emmel, Neil Brown, Trond Myklebust, Erez Zadok, and Ion Badulescu also provided valuable comments and contributions.

2.1. What is NFS?

The Network File System (NFS) was developed to allow machines to mount a disk partition on a remote machine as if it were on a local hard drive. This allows for fast, seamless sharing of files across a network.

It also gives the potential for unwanted people to access your hard drive over the network (and thereby possibly read your email and delete all your files as well as break into your system) if you set it up incorrectly. So please read the Security section of this document carefully if you intend to implement an NFS setup.

There are other systems that provide similar functionality to NFS. Samba (http://www.samba.org) provides file services to Windows clients. The Andrew File System from IBM (http://www.transarc.com/Product/EFS/AFS/index.html), recently open-sourced, provides a file sharing mechanism with some additional security and performance features. The Coda File System (http://www.coda.cs.cmu.edu/) is still in development as of this writing but is designed to work well with disconnected clients. Many of the features of the Andrew and Coda file systems are slated for inclusion in the next version of NFS (Version 4) (http://www.nfsv4.org). The advantage of NFS today is that it is mature, standard, well understood, and supported robustly across a variety of platforms.

2.2. What is this HOWTO and what is it not?

This HOWTO is intended as a complete, step-by-step guide to setting up NFS correctly and effectively. Setting up NFS involves two steps, namely configuring the server and then configuring the client. Each of these steps is dealt with in order. The document then offers some tips for people with particular needs and hardware setups, as well as security and troubleshooting advice.

This HOWTO is not a description of the guts and underlying structure of NFS. For that you may wish to read Linux NFS and Automounter Administration by Erez Zadok (Sybex, 2001). The classic NFS book, updated and still quite useful, is Managing NFS and NIS by Hal Stern, published by O'Reilly & Associates, Inc. A much more advanced technical description of NFS is available in NFS Illustrated by Brent Callaghan.

This document is also not intended as a complete reference manual, and does not contain an exhaustive list of the features of Linux NFS. For that, you can look at the man pages for nfs(5), exports(5), mount(8), fstab(5), nfsd(8), lockd(8), statd(8), rquotad(8), and mountd(8).

It will also not cover PC-NFS, which is considered obsolete (users are encouraged to use Samba to share files with Windows machines) or NFS Version 4, which is still in development.

2.3. Knowledge Pre-Requisites

You should know some basic things about TCP/IP networking before reading this HOWTO; if you are in doubt, read the Networking- Overview-HOWTO.

2.4. Software Pre-Requisites: Kernel Version and nfs-utils

The difference between Version 2 NFS and version 3 NFS will be explained later on; for now, you might simply take the suggestion that you will need NFS Version 3 if you are installing a dedicated or high-volume file server. NFS Version 2 should be fine for casual use.

NFS Version 2 has been around for quite some time now (at least since the 1.2 kernel series) however you will need a kernel version of at least 2.2.18 if you wish to do any of the following:

• Mix Linux NFS with other operating systems' NFS

• Use file locking reliably over NFS

• Use NFS Version 3.

2.5. Where to get help and further information

As of November 2000, the Linux NFS homepage is at http://nfs.sourceforge.net. Please check there for NFS related mailing lists as well as the latest version of nfs-utils, NFS kernel patches, and other NFS related packages.

When you encounter a problem or have a question not covered in this manual, the faq or the man pages, you should send a message to the nfs mailing list (<[email protected]>). To best help the developers and other users help you assess your problem you should include:

• the version of nfs-utils you are using

• the version of the kernel and any non-stock applied kernels.

• the distribution of linux you are using

• the version(s) of other operating systems involved.

It is also useful to know the networking configuration connecting the hosts.

If your problem involves the inability mount or export shares please also include:

• a copy of your /etc/exports file

• the output of rpcinfo -p localhost run on the server

• the output of rpcinfo -p servername run on the client

Sending all of this information with a specific question, after reading all the documentation, is the best way to ensure a helpful response from the list.

You may also wish to look at the man pages for nfs(5), exports(5), mount(8), fstab(5), nfsd(8), lockd(8), statd(8), rquotad(8), and mountd(8).

3.1. Introduction to the server setup

It is assumed that you will be setting up both a server and a client. If you are just setting up a client to work off of somebody else's server (say in your department), you can skip to Section 4. However, every client that is set up requires modifications on the server to authorize that client (unless the server setup is done in a very insecure way), so even if you are not setting up a server you may wish to read this section to get an idea what kinds of authorization problems to look out for.

Setting up the server will be done in two steps: Setting up the configuration files for NFS, and then starting the NFS services.

3.2. Setting up the Configuration Files

There are three main configuration files you will need to edit to set up an NFS server: /etc/exports, /etc/hosts.allow, and /etc/hosts.deny. Strictly speaking, you only need to edit /etc/exports to get NFS to work, but you would be left with an extremely insecure setup. You may also need to edit your startup scripts; see Section 3.3.3 for more on that.

    service: host [or network/netmask] , host [or network/netmask]
   

   portmap: 192.168.0.1 , 192.168.0.2
   

    lockd: 192.168.0.1 , 192.168.0.2
    rquotad: 192.168.0.1 , 192.168.0.2
    mountd: 192.168.0.1 , 192.168.0.2
    statd: 192.168.0.1 , 192.168.0.2
   

3.3. Getting the services started

3.4. Verifying that NFS is running

To do this, query the portmapper with the command rpcinfo -p to find out what services it is providing. You should get something like this:

program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100011 1 udp 749 rquotad 100011 2 udp 749 rquotad 100005 1 udp 759 mountd 100005 1 tcp 761 mountd 100005 2 udp 764 mountd 100005 2 tcp 766 mountd 100005 3 udp 769 mountd 100005 3 tcp 771 mountd 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 300019 1 tcp 830 amd 300019 1 udp 831 amd 100024 1 udp 944 status 100024 1 tcp 946 status 100021 1 udp 1042 nlockmgr 100021 3 udp 1042 nlockmgr 100021 4 udp 1042 nlockmgr 100021 1 tcp 1629 nlockmgr 100021 3 tcp 1629 nlockmgr 100021 4 tcp 1629 nlockmgr

This says that we have NFS versions 2 and 3, rpc.statd version 1, network lock manager (the service name for rpc.lockd) versions 1, 3, and 4. There are also different service listings depending on whether NFS is travelling over TCP or UDP. Linux systems use UDP by default unless TCP is explicitly requested; however other OSes such as Solaris default to TCP.

If you do not at least see a line that says portmapper, a line that says nfs, and a line that says mountd then you will need to backtrack and try again to start up the daemons (see Section 7, Troubleshooting, if this still doesn't work).

If you do see these services listed, then you should be ready to set up NFS clients to access files from your server.

3.5. Making changes to /etc/exports later on

If you come back and change your /etc/exports file, the changes you make may not take effect immediately. You should run the command exportfs -ra to force nfsd to re-read the /etc/exports � file. If you can't find the exportfs command, then you can kill nfsd with the -HUP flag (see the man pages for kill for details).

If that still doesn't work, don't forget to check hosts.allow to make sure you haven't forgotten to list any new client machines there. Also check the host listings on any firewalls you may have set up (see Section 7 and Section 6 for more details on firewalls and NFS).

4.1. Mounting remote directories

Before beginning, you should double-check to make sure your mount program is new enough (version 2.10m if you want to use Version 3 NFS), and that the client machine supports NFS mounting, though most standard distributions do. If you are using a 2.2 or later kernel with the /proc filesystem you can check the latter by reading the file /proc/filesystems and making sure there is a line containing nfs. If not, typing insmod nfs may make it magically appear if NFS has been compiled as a module; otherwise, you will need to build (or download) a kernel that has NFS support built in. In general, kernels that do not have NFS compiled in will give a very specific error when the mount command below is run.

To begin using machine as an NFS client, you will need the portmapper running on that machine, and to use NFS file locking, you will also need rpc.statd and rpc.lockd running on both the client and the server. Most recent distributions start those services by default at boot time; if yours doesn't, see Section 3.2 for information on how to start them up.

With portmap, lockd, and statd running, you should now be able to mount the remote directory from your server just the way you mount a local hard drive, with the mount command. Continuing our example from the previous section, suppose our server above is called master.foo.com,and we want to mount the /home directory on slave1.foo.com. Then, all we have to do, from the root prompt on slave1.foo.com, is type:

# mount master.foo.com:/home /mnt/home

and the directory /home on master will appear as the directory /mnt/home on slave1. (Note that this assumes we have created the directory /mnt/home as an empty mount point beforehand.)

If this does not work, see the Troubleshooting section (Section 7).

You can get rid of the file system by typing

# umount /mnt/home

just like you would for a local file system.

4.2. Getting NFS File Systems to Be Mounted at Boot Time

NFS file systems can be added to your /etc/fstab file the same way local file systems can, so that they mount when your system starts up. The only difference is that the file system type will be set to nfs and the dump and fsck order (the last two entries) will have to be set to zero. So for our example above, the entry in /etc/fstab would look like:

# device mountpoint fs-type options dump fsckorder ... master.foo.com:/home /mnt nfs rw 0 0 ...

See the man pages for fstab if you are unfamiliar with the syntax of this file. If you are using an automounter such as amd or autofs, the options in the corresponding fields of your mount listings should look very similar if not identical.

At this point you should have NFS working, though a few tweaks may still be necessary to get it to work well. You should also read Section 6 to be sure your setup is reasonably secure.

4.3. Mount options

5.1. Setting Block Size to Optimize Transfer Speeds

The mount command options rsize and wsize specify the size of the chunks of data that the client and server pass back and forth to each other. If no rsize and wsize options are specified, the default varies by which version of NFS we are using. The most common default is 4K (4096 bytes), although for TCP-based mounts in 2.2 kernels, and for all mounts beginning with 2.4 kernels, the server specifies the default block size.

The theoretical limit for the NFS V2 protocol is 8K. For the V3 protocol, the limit is specific to the server. On the Linux server, the maximum block size is defined by the value of the kernel constant NFSSVC_MAXBLKSIZE, found in the Linux kernel source file ./include/linux/nfsd/const.h. The current maximum block size for the kernel, as of 2.4.17, is 8K (8192 bytes), but the patch set implementing NFS over TCP/IP transport in the 2.4 series, as of this writing, uses a value of 32K (defined in the patch as 32*1024) for the maximum block size.

All 2.4 clients currently support up to 32K block transfer sizes, allowing the standard 32K block transfers across NFS mounts from other servers, such as Solaris, without client modification.

The defaults may be too big or too small, depending on the specific combination of hardware and kernels. On the one hand, some combinations of Linux kernels and network cards (largely on older machines) cannot handle blocks that large. On the other hand, if they can handle larger blocks, a bigger size might be faster.

You will want to experiment and find an rsize and wsize that works and is as fast as possible. You can test the speed of your options with some simple commands, if your network environment is not heavily used. Note that your results may vary widely unless you resort to using more complex benchmarks, such as Bonnie, Bonnie++, or IOzone.

The first of these commands transfers 16384 blocks of 16k each from the special file /dev/zero (which if you read it just spits out zeros really fast) to the mounted partition. We will time it to see how long it takes. So, from the client machine, type:

    # time dd if=/dev/zero of=/mnt/home/testfile bs=16k count=16384

This creates a 256Mb file of zeroed bytes. In general, you should create a file that's at least twice as large as the system RAM on the server, but make sure you have enough disk space! Then read back the file into the great black hole on the client machine (/dev/null) by typing the following:

    # time dd if=/mnt/home/testfile of=/dev/null bs=16k

Repeat this a few times and average how long it takes. Be sure to unmount and remount the filesystem each time (both on the client and, if you are zealous, locally on the server as well), which should clear out any caches.

Then unmount, and mount again with a larger and smaller block size. They should be multiples of 1024, and not larger than the maximum block size allowed by your system. Note that NFS Version 2 is limited to a maximum of 8K, regardless of the maximum block size defined by NFSSVC_MAXBLKSIZE; Version 3 will support up to 64K, if permitted. The block size should be a power of two since most of the parameters that would constrain it (such as file system block sizes and network packet size) are also powers of two. However, some users have reported better successes with block sizes that are not powers of two but are still multiples of the file system block size and the network packet size.

Directly after mounting with a larger size, cd into the mounted file system and do things like ls, explore the filesystem a bit to make sure everything is as it should. If the rsize/wsize is too large the symptoms are very odd and not 100% obvious. A typical symptom is incomplete file lists when doing ls, and no error messages, or reading files failing mysteriously with no error messages. After establishing that the given rsize/ wsize works you can do the speed tests again. Different server platforms are likely to have different optimal sizes.

Remember to edit /etc/fstab to reflect the rsize/wsize you found to be the most desirable.

If your results seem inconsistent, or doubtful, you may need to analyze your network more extensively while varying the rsize and wsize values. In that case, here are several pointers to benchmarks that may prove useful:

• Bonnie http://www.textuality.com/bonnie/

• Bonnie++ http://www.coker.com.au/bonnie++/

• IOzone file system benchmark http://www.iozone.org/

• The official NFS benchmark, SPECsfs97 http://www.spec.org/osg/sfs97/

The easiest benchmark with the widest coverage, including an extensive spread of file sizes, and of IO types - reads, & writes, rereads & rewrites, random access, etc. - seems to be IOzone. A recommended invocation of IOzone (for which you must have root privileges) includes unmounting and remounting the directory under test, in order to clear out the caches between tests, and including the file close time in the measurements. Assuming you've already exported /tmp to everyone from the server foo, and that you've installed IOzone in the local directory, this should work:

    # echo "foo:/tmp /mnt/foo nfs rw,hard,intr,rsize=8192,wsize=8192 0 0"
    >> /etc/fstab
    # mkdir /mnt/foo
    # mount /mnt/foo
    # ./iozone -a -R -c -U /mnt/foo -f /mnt/foo/testfile > logfile

The benchmark should take 2-3 hours at most, but of course you will need to run it for each value of rsize and wsize that is of interest. The web site gives full documentation of the parameters, but the specific options used above are:

• -a Full automatic mode, which tests file sizes of 64K to 512M, using record sizes of 4K to 16M

• -R Generate report in excel spreadsheet form (The "surface plot" option for graphs is best)

• -c Include the file close time in the tests, which will pick up the NFS version 3 commit time

• -U Use the given mount point to unmount and remount between tests; it clears out caches

• -f When using unmount, you have to locate the test file in the mounted file system

5.2. Packet Size and Network Drivers

While many Linux network card drivers are excellent, some are quite shoddy, including a few drivers for some fairly standard cards. It is worth experimenting with your network card directly to find out how it can best handle traffic.

Try pinging back and forth between the two machines with large packets using the -f and -s options with ping (see ping(8) for more details) and see if a lot of packets get dropped, or if they take a long time for a reply. If so, you may have a problem with the performance of your network card.

For a more extensive analysis of NFS behavior in particular, use the nfsstat command to look at nfs transactions, client and server statistics, network statistics, and so forth. The "-o net" option will show you the number of dropped packets in relation to the total number of transactions. In UDP transactions, the most important statistic is the number of retransmissions, due to dropped packets, socket buffer overflows, general server congestion, timeouts, etc. This will have a tremendously important effect on NFS performance, and should be carefully monitored. Note that nfsstat does not yet implement the -z option, which would zero out all counters, so you must look at the current nfsstat counter values prior to running the benchmarks.

To correct network problems, you may wish to reconfigure the packet size that your network card uses. Very often there is a constraint somewhere else in the network (such as a router) that causes a smaller maximum packet size between two machines than what the network cards on the machines are actually capable of. TCP should autodiscover the appropriate packet size for a network, but UDP will simply stay at a default value. So determining the appropriate packet size is especially important if you are using NFS over UDP.

You can test for the network packet size using the tracepath command: From the client machine, just type tracepath server 2049 and the path MTU should be reported at the bottom. You can then set the MTU on your network card equal to the path MTU, by using the MTU option to ifconfig, and see if fewer packets get dropped. See the ifconfig man pages for details on how to reset the MTU.

In addition, netstat -s will give the statistics collected for traffic across all supported protocols. You may also look at /proc/net/snmp for information about current network behavior; see the next section for more details.

5.3. Overflow of Fragmented Packets

Using an rsize or wsize larger than your network's MTU (often set to 1500, in many networks) will cause IP packet fragmentation when using NFS over UDP. IP packet fragmentation and reassembly require a significant amount of CPU resource at both ends of a network connection. In addition, packet fragmentation also exposes your network traffic to greater unreliability, since a complete RPC request must be retransmitted if a UDP packet fragment is dropped for any reason. Any increase of RPC retransmissions, along with the possibility of increased timeouts, are the single worst impediment to performance for NFS over UDP.

Packets may be dropped for many reasons. If your network topography is complex, fragment routes may differ, and may not all arrive at the Server for reassembly. NFS Server capacity may also be an issue, since the kernel has a limit of how many fragments it can buffer before it starts throwing away packets. With kernels that support the /proc filesystem, you can monitor the files /proc/sys/net/ipv4/ipfrag_high_thresh and /proc/sys/net/ipv4/ipfrag_low_thresh. Once the number of unprocessed, fragmented packets reaches the number specified by ipfrag_high_thresh (in bytes), the kernel will simply start throwing away fragmented packets until the number of incomplete packets reaches the number specified by ipfrag_low_thresh.

Another counter to monitor is IP: ReasmFails in the file /proc/net/snmp; this is the number of fragment reassembly failures. if it goes up too quickly during heavy file activity, you may have problem.

5.4. NFS over TCP

A new feature, available for both 2.4 and 2.5 kernels but not yet integrated into the mainstream kernel at the time of this writing, is NFS over TCP. Using TCP has a distinct advantage and a distinct disadvantage over UDP. The advantage is that it works far better than UDP on lossy networks. When using TCP, a single dropped packet can be retransmitted, without the retransmission of the entire RPC request, resulting in better performance on lossy networks. In addition, TCP will handle network speed differences better than UDP, due to the underlying flow control at the network level.

The disadvantage of using TCP is that it is not a stateless protocol like UDP. If your server crashes in the middle of a packet transmission, the client will hang and any shares will need to be unmounted and remounted.

The overhead incurred by the TCP protocol will result in somewhat slower performance than UDP under ideal network conditions, but the cost is not severe, and is often not noticable without careful measurement. If you are using gigabit ethernet from end to end, you might also investigate the usage of jumbo frames, since the high speed network may allow the larger frame sizes without encountering increased collision rates, particularly if you have set the network to full duplex.

5.5. Timeout and Retransmission Values

Two mount command options, timeo and retrans, control the behavior of UDP requests when encountering client timeouts due to dropped packets, network congestion, and so forth. The -o timeo option allows designation of the length of time, in tenths of seconds, that the client will wait until it decides it will not get a reply from the server, and must try to send the request again. The default value is 7 tenths of a second. The -o retrans option allows designation of the number of timeouts allowed before the client gives up, and displays the Server not responding message. The default value is 3 attempts. Once the client displays this message, it will continue to try to send the request, but only once before displaying the error message if another timeout occurs. When the client reestablishes contact, it will fall back to using the correct retrans value, and will display the Server OK message.

If you are already encountering excessive retransmissions (see the output of the nfsstat command), or want to increase the block transfer size without encountering timeouts and retransmissions, you may want to adjust these values. The specific adjustment will depend upon your environment, and in most cases, the current defaults are appropriate.

5.6. Number of Instances of the NFSD Server Daemon

Most startup scripts, Linux and otherwise, start 8 instances of nfsd. In the early days of NFS, Sun decided on this number as a rule of thumb, and everyone else copied. There are no good measures of how many instances are optimal, but a more heavily-trafficked server may require more. You should use at the very least one daemon per processor, but four to eight per processor may be a better rule of thumb. If you are using a 2.4 or higher kernel and you want to see how heavily each nfsd thread is being used, you can look at the file /proc/net/rpc/nfsd. The last ten numbers on the th line in that file indicate the number of seconds that the thread usage was at that percentage of the maximum allowable. If you have a large number in the top three deciles, you may wish to increase the number of nfsd instances. This is done upon starting nfsd using the number of instances as the command line option, and is specified in the NFS startup script (/etc/rc.d/init.d/nfs on Red Hat) as RPCNFSDCOUNT. See the nfsd(8) man page for more information.

5.7. Memory Limits on the Input Queue

On 2.2 and 2.4 kernels, the socket input queue, where requests sit while they are currently being processed, has a small default size limit (rmem_default) of 64k. This queue is important for clients with heavy read loads, and servers with heavy write loads. As an example, if you are running 8 instances of nfsd on the server, each will only have 8k to store write requests while it processes them. In addition, the socket output queue - important for clients with heavy write loads and servers with heavy read loads - also has a small default size (wmem_default).

Several published runs of the NFS benchmark SPECsfs specify usage of a much higher value for both the read and write value sets, [rw]mem_default and [rw]mem_max. You might consider increasing these values to at least 256k. The read and write limits are set in the proc file system using (for example) the files /proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_max. The rmem_default value can be increased in three steps; the following method is a bit of a hack but should work and should not cause any problems:

• Increase the size listed in the file:

  # echo 262144 > /proc/sys/net/core/rmem_default # echo 262144 > /proc/sys/net/core/rmem_max

• Restart NFS. For example, on Red Hat systems,

  # /etc/rc.d/init.d/nfs restart

• You might return the size limits to their normal size in case other kernel systems depend on it:

  # echo 65536 > /proc/sys/net/core/rmem_default # echo 65536 > /proc/sys/net/core/rmem_max

This last step may be necessary because machines have been reported to crash if these values are left changed for long periods of time.

5.8. Turning Off Autonegotiation of NICs and Hubs

If network cards auto-negotiate badly with hubs and switches, and ports run at different speeds, or with different duplex configurations, performance will be severely impacted due to excessive collisions, dropped packets, etc. If you see excessive numbers of dropped packets in the nfsstat output, or poor network performance in general, try playing around with the network speed and duplex settings. If possible, concentrate on establishing a 100BaseT full duplex subnet; the virtual elimination of collisions in full duplex will remove the most severe performance inhibitor for NFS over UDP. Be careful when turning off autonegotiation on a card: The hub or switch that the card is attached to will then resort to other mechanisms (such as parallel detection) to determine the duplex settings, and some cards default to half duplex because it is more likely to be supported by an old hub. The best solution, if the driver supports it, is to force the card to negotiate 100BaseT full duplex.

5.9. Synchronous vs. Asynchronous Behavior in NFS

The default export behavior for both NFS Version 2 and Version 3 protocols, used by exportfs in nfs-utils versions prior to Version 1.11 (the latter is in the CVS tree, but not yet released in a package, as of January, 2002) is "asynchronous". This default permits the server to reply to client requests as soon as it has processed the request and handed it off to the local file system, without waiting for the data to be written to stable storage. This is indicated by the async option denoted in the server's export list. It yields better performance at the cost of possible data corruption if the server reboots while still holding unwritten data and/or metadata in its caches. This possible data corruption is not detectable at the time of occurrence, since the async option instructs the server to lie to the client, telling the client that all data has indeed been written to the stable storage, regardless of the protocol used.

In order to conform with "synchronous" behavior, used as the default for most proprietary systems supporting NFS (Solaris, HP-UX, RS/6000, etc.), and now used as the default in the latest version of exportfs, the Linux Server's file system must be exported with the sync option. Note that specifying synchronous exports will result in no option being seen in the server's export list:

• Export a couple file systems to everyone, using slightly different options:

  # /usr/sbin/exportfs -o rw,sync *:/usr/local # /usr/sbin/exportfs -o rw *:/tmp

• Now we can see what the exported file system parameters look like:

  # /usr/sbin/exportfs -v /usr/local *(rw) /tmp *(rw,async)

If your kernel is compiled with the /proc filesystem, then the file /proc/fs/nfs/exports will also show the full list of export options.

When synchronous behavior is specified, the server will not complete (that is, reply to the client) an NFS version 2 protocol request until the local file system has written all data/metadata to the disk. The server will complete a synchronous NFS version 3 request without this delay, and will return the status of the data in order to inform the client as to what data should be maintained in its caches, and what data is safe to discard. There are 3 possible status values, defined an enumerated type, nfs3_stable_how, in include/linux/nfs.h. The values, along with the subsequent actions taken due to these results, are as follows:

• NFS_UNSTABLE - Data/Metadata was not committed to stable storage on the server, and must be cached on the client until a subsequent client commit request assures that the server does send data to stable storage.

• NFS_DATA_SYNC - Metadata was not sent to stable storage, and must be cached on the client. A subsequent commit is necessary, as is required above.

• NFS_FILE_SYNC - No data/metadata need be cached, and a subsequent commit need not be sent for the range covered by this request.

In addition to the above definition of synchronous behavior, the client may explicitly insist on total synchronous behavior, regardless of the protocol, by opening all files with the O_SYNC option. In this case, all replies to client requests will wait until the data has hit the server's disk, regardless of the protocol used (meaning that, in NFS version 3, all requests will be NFS_FILE_SYNC requests, and will require that the Server returns this status). In that case, the performance of NFS Version 2 and NFS Version 3 will be virtually identical.

If, however, the old default async behavior is used, the O_SYNC option has no effect at all in either version of NFS, since the server will reply to the client without waiting for the write to complete. In that case the performance differences between versions will also disappear.

Finally, note that, for NFS version 3 protocol requests, a subsequent commit request from the NFS client at file close time, or at fsync() time, will force the server to write any previously unwritten data/metadata to the disk, and the server will not reply to the client until this has been completed, as long as sync behavior is followed. If async is used, the commit is essentially a no-op, since the server once again lies to the client, telling the client that the data has been sent to stable storage. This again exposes the client and server to data corruption, since cached data may be discarded on the client due to its belief that the server now has the data maintained in stable storage.

5.10. Non-NFS-Related Means of Enhancing Server Performance

In general, server performance and server disk access speed will have an important effect on NFS performance. Offering general guidelines for setting up a well-functioning file server is outside the scope of this document, but a few hints may be worth mentioning:

• If you have access to RAID arrays, use RAID 1/0 for both write speed and redundancy; RAID 5 gives you good read speeds but lousy write speeds.

• A journalling filesystem will drastically reduce your reboot time in the event of a system crash. Currently, ext3 will work correctly with NFS version 3. In addition, Reiserfs version 3.6 will work with NFS version 3 on 2.4.7 or later kernels (patches are available for previous kernels). Earlier versions of Reiserfs did not include room for generation numbers in the inode, exposing the possibility of undetected data corruption during a server reboot.

• Additionally, journalled file systems can be configured to maximize performance by taking advantage of the fact that journal updates are all that is necessary for data protection. One example is using ext3 with data=journal so that all updates go first to the journal, and later to the main file system. Once the journal has been updated, the NFS server can safely issue the reply to the clients, and the main file system update can occur at the server's leisure.

  The journal in a journalling file system may also reside on a separate device such as a flash memory card so that journal updates normally require no seeking. With only rotational delay imposing a cost, this gives reasonably good synchronous IO performance. Note that ext3 currently supports journal relocation, and ReiserFS will (officially) support it soon. The Reiserfs tool package found at ftp://ftp.namesys.com/pub/reiserfsprogs/reiserfsprogs-3.x.0k.tar.gz contains the reiserfstune tool, which will allow journal relocation. It does, however, require a kernel patch which has not yet been officially released as of January, 2002.

• Using an automounter (such as autofs or amd) may prevent hangs if you cross-mount files on your machines (whether on purpose or by oversight) and one of those machines goes down. See the Automount Mini-HOWTO for details.

• Some manufacturers (Network Appliance, Hewlett Packard, and others) provide NFS accelerators in the form of Non-Volatile RAM. NVRAM will boost access speed to stable storage up to the equivalent of async access.

6.1. The portmapper

The portmapper keeps a list of what services are running on what ports. This list is used by a connecting machine to see what ports it wants to talk to access certain services.

The portmapper is not in as bad a shape as a few years ago but it is still a point of worry for many sys admins. The portmapper, like NFS and NIS, should not really have connections made to it outside of a trusted local area network. If you have to expose them to the outside world - be careful and keep up diligent monitoring of those systems.

Not all Linux distributions were created equal. Some seemingly up-to-date distributions do not include a securable portmapper. The easy way to check if your portmapper is good or not is to run strings(1) and see if it reads the relevant files, /etc/hosts.deny and /etc/hosts.allow. Assuming your portmapper is /sbin/portmap you can check it with this command:

strings /sbin/portmap | grep hosts.

On a securable machine it comes up something like this:

/etc/hosts.allow /etc/hosts.deny @(#) hosts_ctl.c 1.4 94/12/28 17:42:27 @(#) hosts_access.c 1.21 97/02/12 02:13:22

First we edit /etc/hosts.deny. It should contain the line

portmap: ALL

which will deny access to everyone. While it is closed run:

rpcinfo -p

just to check that your portmapper really reads and obeys this file. Rpcinfo should give no output, or possibly an error message. The files /etc/hosts.allow and /etc/hosts.deny take effect immediately after you save them. No daemon needs to be restarted.

Closing the portmapper for everyone is a bit drastic, so we open it again by editing /etc/hosts.allow. But first we need to figure out what to put in it. It should basically list all machines that should have access to your portmapper. On a run of the mill Linux system there are very few machines that need any access for any reason. The portmapper administers nfsd, mountd, ypbind/ypserv, rquotad, lockd (which shows up as nlockmgr), statd (which shows up as status) and 'r' services like ruptime and rusers. Of these only nfsd, mountd, ypbind/ypserv and perhaps rquotad,lockd and statd are of any consequence. All machines that need to access services on your machine should be allowed to do that. Let's say that your machine's address is 192.168.0.254 and that it lives on the subnet 192.168.0.0, and that all machines on the subnet should have access to it (for an overview of those terms see the the Networking-Overview-HOWTO). Then we write:

portmap: 192.168.0.0/255.255.255.0

in /etc/hosts.allow. If you are not sure what your network or netmask are, you can use the ifconfig command to determine the netmask and the netstat command to determine the network. For, example, for the device eth0 on the above machine ifconfig should show:

... eth0 Link encap:Ethernet HWaddr 00:60:8C:96:D5:56 inet addr:192.168.0.254 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:360315 errors:0 dropped:0 overruns:0 TX packets:179274 errors:0 dropped:0 overruns:0 Interrupt:10 Base address:0x320 ...

and netstat -rn should show:

Kernel routing table Destination Gateway Genmask Flags Metric Ref Use Iface ... 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 174412 eth0 ...

(The network address is in the first column).

The /etc/hosts.deny and /etc/hosts.allow files are described in the manual pages of the same names.

IMPORTANT: Do not put anything but IP NUMBERS in the portmap lines of these files. Host name lookups can indirectly cause portmap activity which will trigger host name lookups which can indirectly cause portmap activity which will trigger...

Versions 0.2.0 and higher of the nfs-utils package also use the hosts.allow and hosts.deny files, so you should put in entries for lockd, statd, mountd, and rquotad in these files too. For a complete example, see Section 3.2.2.

The above things should make your server tighter. The only remaining problem is if someone gains administrative access to one of your trusted client machines and is able to send bogus NFS requests. The next section deals with safeguards against this problem.

6.2. Server security: nfsd and mountd

On the server we can decide that we don't want to trust any requests made as root on the client. We can do that by using the root_squash option in /etc/exports:

/home slave1(rw,root_squash)

This is, in fact, the default. It should always be turned on unless you have a very good reason to turn it off. To turn it off use the no_root_squash option.

Now, if a user with UID 0 (i.e., root's user ID number) on the client attempts to access (read, write, delete) the file system, the server substitutes the UID of the server's 'nobody' account. Which means that the root user on the client can't access or change files that only root on the server can access or change. That's good, and you should probably use root_squash on all the file systems you export. "But the root user on the client can still use su to become any other user and access and change that users files!" say you. To which the answer is: Yes, and that's the way it is, and has to be with Unix and NFS. This has one important implication: All important binaries and files should be owned by root, and not bin or other non-root account, since the only account the clients root user cannot access is the servers root account. In the exports(5) man page there are several other squash options listed so that you can decide to mistrust whomever you (don't) like on the clients.

The TCP ports 1-1024 are reserved for root's use (and therefore sometimes referred to as "secure ports") A non-root user cannot bind these ports. Adding the secure option to an /etc/exports means that it will only listed to requests coming from ports 1-1024 on the client, so that a malicious non-root user on the client cannot come along and open up a spoofed NFS dialogue on a non-reserved port. This option is set by default.

6.3. Client Security

6.4. NFS and firewalls (ipchains and netfilter)

IPchains (under the 2.2.X kernels) and netfilter (under the 2.4.x kernels) allow a good level of security - instead of relying on the daemon (or perhaps its TCP wrapper) to determine which machines can connect, the connection attempt is allowed or disallowed at a lower level. In this case, you can stop the connection much earlier and more globally, which can protect you from all sorts of attacks.

Describing how to set up a Linux firewall is well beyond the scope of this document. Interested readers may wish to read the Firewall-HOWTO or the IPCHAINS-HOWTO. For users of kernel 2.4 and above you might want to visit the netfilter webpage at: http://netfilter.filewatcher.org. If you are already familiar with the workings of ipchains or netfilter this section will give you a few tips on how to better setup your NFS daemons to more easily firewall and protect them.

A good rule to follow for your firewall configuration is to deny all, and allow only some - this helps to keep you from accidentally allowing more than you intended.

In order to understand how to firewall the NFS daemons, it will help to breifly review how they bind to ports.

When a daemon starts up, it requests a free port from the portmapper. The portmapper gets the port for the daemon and keeps track of the port currently used by that daemon. When other hosts or processes need to communicate with the daemon, they request the port number from the portmapper in order to find the daemon. So the ports will perpetually float because different ports may be free at different times and so the portmapper will allocate them differently each time. This is a pain for setting up a firewall. If you never know where the daemons are going to be then you don't know precisely which ports to allow access to. This might not be a big deal for many people running on a protected or isolated LAN. For those people on a public network, though, this is horrible.

In kernels 2.4.13 and later with nfs-utils 0.3.3 or later you no longer have to worry about the floating of ports in the portmapper. Now all of the daemons pertaining to nfs can be "pinned" to a port. Most of them nicely take a -p option when they are started; those daemons that are started by the kernel take some kernel arguments or module options. They are described below.

Some of the daemons involved in sharing data via nfs are already bound to a port. portmap is always on port 111 tcp and udp. nfsd is always on port 2049 TCP and UDP (however, as of kernel 2.4.17, NFS over TCP is considered experimental and is not for use on production machines).

The other daemons, statd, mountd, lockd, and rquotad, will normally move around to the first available port they are informed of by the portmapper.

To force statd to bind to a particular port, use the -p portnum option. To force statd to respond on a particular port, additionally use the -o portnum option when starting it.

To force mountd to bind to a particular port use the -p portnum option.

For example, to have statd broadcast of port 32765 and listen on port 32766, and mountd listen on port 32767, you would type:

# statd -p 32765 -o 32766
# mountd -p 32767

lockd is started by the kernel when it is needed. Therefore you need to pass module options (if you have it built as a module) or kernel options to force lockd to listen and respond only on certain ports.

If you are using loadable modules and you would like to specify these options in your /etc/modules.conf file add a line like this to the file:

options lockd nlm_udpport=32768 nlm_tcpport=32768

The above line would specify the udp and tcp port for lockd to be 32768.

If you are not using loadable modules or if you have compiled lockd into the kernel instead of building it as a module then you will need to pass it an option on the kernel boot line.

It should look something like this:

 vmlinuz 3 root=/dev/hda1 lockd.udpport=32768 lockd.tcpport=32768

The port numbers do not have to match but it would simply add unnecessary confusion if they didn't.

If you are using quotas and using rpc.quotad to make these quotas viewable over nfs you will need to also take it into account when setting up your firewall. There are two rpc.rquotad source trees. One of those is maintained in the nfs-utils tree. The other in the quota-tools tree. They do not operate identically. The one provided with nfs-utils supports binding the daemon to a port with the -p directive. The one in quota-tools does not. Consult your distribution's documentation to determine if yours does.

For the sake of this discussion lets describe a network and setup a firewall to protect our nfs server. Our nfs server is 192.168.0.42 our client is 192.168.0.45 only. As in the example above, statd has been started so that it only binds to port 32765 for incoming requests and it must answer on port 32766. mountd is forced to bind to port 32767. lockd's module parameters have been set to bind to 32768. nfsd is, of course, on port 2049 and the portmapper is on port 111.

We are not using quotas.

Using IPCHAINS, a simple firewall might look something like this:

ipchains -A input -f -j ACCEPT -s 192.168.0.45
ipchains -A input -s 192.168.0.45 -d 0/0 32765:32768 -p 6 -j ACCEPT
ipchains -A input -s 192.168.0.45 -d 0/0 32765:32768 -p 17 -j ACCEPT
ipchains -A input -s 192.168.0.45 -d 0/0 2049 -p 17 -j ACCEPT
ipchains -A input -s 192.168.0.45 -d 0/0 2049 -p 6 -j ACCEPT
ipchains -A input -s 192.168.0.45 -d 0/0 111 -p 6 -j ACCEPT
ipchains -A input -s 192.168.0.45 -d 0/0 111 -p 17 -j ACCEPT
ipchains -A input -s 0/0 -d 0/0 -p 6 -j DENY -y -l
ipchains -A input -s 0/0 -d 0/0 -p 17 -j DENY -l

The equivalent set of commands in netfilter is:

iptables -A INPUT -f -j ACCEPT -s 192.168.0.45
iptables -A INPUT -s 192.168.0.45 -d 0/0 32765:32768 -p 6 -j ACCEPT
iptables -A INPUT -s 192.168.0.45 -d 0/0 32765:32768 -p 17 -j ACCEPT
iptables -A INPUT -s 192.168.0.45 -d 0/0 2049 -p 17 -j ACCEPT
iptables -A INPUT -s 192.168.0.45 -d 0/0 2049 -p 6 -j ACCEPT
iptables -A INPUT -s 192.168.0.45 -d 0/0 111 -p 6 -j ACCEPT
iptables -A INPUT -s 192.168.0.45 -d 0/0 111 -p 17 -j ACCEPT
iptables -A INPUT -s 0/0 -d 0/0 -p 6 -j DENY --syn --log-level 5
iptables -A INPUT -s 0/0 -d 0/0 -p 17 -j DENY --log-level 5

The first line says to accept all packet fragments (except the first packet fragment which will be treated as a normal packet). In theory no packet will pass through until it is reassembled, and it won't be reassembled unless the first packet fragment is passed. Of course there are attacks that can be generated by overloading a machine with packet fragments. But NFS won't work correctly unless you let fragments through. See Section 7.8 for details.

The other lines allow specific connections from any port on our client host to the specific ports we have made available on our server. This means that if, say, 192.158.0.46 attempts to contact the NFS server it will not be able to mount or see what mounts are available.

With the new port pinning capabilities it is obviously much easier to control what hosts are allowed to mount your NFS shares. It is worth mentioning that NFS is not an encrypted protocol and anyone on the same physical network could sniff the traffic and reassemble the information being passed back and forth.

6.5. Tunneling NFS through SSH

One method of encrypting NFS traffic over a network is to use the port-forwarding capabilities of ssh. However, as we shall see, doing so has a serious drawback if you do not utterly and completely trust the local users on your server.

The first step will be to export files to the localhost. For example, to export the /home partition, enter the following into /etc/exports:

/home 127.0.0.1(rw)

The next step is to use ssh to forward ports. For example, ssh can tell the server to forward to any port on any machine from a port on the client. Let us assume, as in the previous section, that our server is 192.168.0.42, and that we have pinned mountd to port 32767 using the argument -p 32767. Then, on the client, we'll type:

# ssh [email protected] -L 250:localhost:2049 -f sleep 60m # ssh [email protected] -L 251:localhost:32767 -f sleep 60m

The above command causes ssh on the client to take any request directed at the client's port 250 and forward it, first through sshd on the server, and then on to the server's port 2049. The second line causes a similar type of forwarding between requests to port 251 on the client and port 32767 on the server. The localhost is relative to the server; that is, the forwarding will be done to the server itself. The port could otherwise have been made to forward to any other machine, and the requests would look to the outside world as if they were coming from the server. Thus, the requests will appear to NFSD on the server as if they are coming from the server itself. Note that in order to bind to a port below 1024 on the client, we have to run this command as root on the client. Doing this will be necessary if we have exported our filesystem with the default secure option.

Finally, we are pulling a little trick with the last option, -f sleep 60m. Normally, when we use ssh, even with the -L option, we will open up a shell on the remote machine. But instead, we just want the port forwarding to execute in the background so that we get our shell on the client back. So, we tell ssh to execute a command in the background on the server to sleep for 60 minutes. This will cause the port to be forwarded for 60 minutes until it gets a connection; at that point, the port will continue to be forwarded until the connection dies or until the 60 minutes are up, whichever happens later. The above command could be put in our startup scripts on the client, right after the network is started.

Next, we have to mount the filesystem on the client. To do this, we tell the client to mount a filesystem on the localhost, but at a different port from the usual 2049. Specifically, an entry in /etc/fstab would look like:

localhost:/home /mnt/home nfs rw,hard,intr,port=250,mountport=251 0 0

Having done this, we can see why the above will be incredibly insecure if we have any ordinary users who are able to log in to the server locally. If they can, there is nothing preventing them from doing what we did and using ssh to forward a privileged port on their own client machine (where they are legitimately root) to ports 2049 and 32767 on the server. Thus, any ordinary user on the server can mount our filesystems with the same rights as root on our client.

If you are using an NFS server that does not have a way for ordinary users to log in, and you wish to use this method, there are two additional caveats: First, the connection travels from the client to the server via sshd; therefore you will have to leave port 22 (where sshd listens) open to your client on the firewall. However you do not need to leave the other ports, such as 2049 and 32767, open anymore. Second, file locking will no longer work. It is not possible to ask statd or the locking manager to make requests to a particular port for a particular mount; therefore, any locking requests will cause statd to connect to statd on localhost, i.e., itself, and it will fail with an error. Any attempt to correct this would require a major rewrite of NFS.

It may also be possible to use IPSec to encrypt network traffic between your client and your server, without compromising any local security on the server; this will not be taken up here. See the FreeS/WAN home page for details on using IPSec under Linux.

6.6. Summary

If you use the hosts.allow, hosts.deny, root_squash, nosuid and privileged port features in the portmapper/NFS software, you avoid many of the presently known bugs in NFS and can almost feel secure about that at least. But still, after all that: When an intruder has access to your network, s/he can make strange commands appear in your .forward or read your mail when /home or /var/mail is NFS exported. For the same reason, you should never access your PGP private key over NFS. Or at least you should know the risk involved. And now you know a bit of it.

NFS and the portmapper makes up a complex subsystem and therefore it's not totally unlikely that new bugs will be discovered, either in the basic design or the implementation we use. There might even be holes known now, which someone is abusing. But that's life.

7.1. Unable to See Files on a Mounted File System

First, check to see if the file system is actually mounted. There are several ways of doing this. The most reliable way is to look at the file /proc/mounts, which will list all mounted filesystems and give details about them. If this doesn't work (for example if you don't have the /proc filesystem compiled into your kernel), you can type mount -f although you get less information.

If the file system appears to be mounted, then you may have mounted another file system on top of it (in which case you should unmount and remount both volumes), or you may have exported the file system on the server before you mounted it there, in which case NFS is exporting the underlying mount point (if so then you need to restart NFS on the server).

If the file system is not mounted, then attempt to mount it. If this does not work, see Symptom 3.

7.2. File requests hang or timeout waiting for access to the file.

This usually means that the client is unable to communicate with the server. See Symptom 3 letter b.

7.3. Unable to mount a file system

There are two common errors that mount produces when it is unable to mount a volume. These are:

1. failed, reason given by server: Permission denied

   This means that the server does not recognize that you have access to the volume.

   1. Check your /etc/exports file and make sure that the volume is exported and that your client has the right kind of access to it. For example, if a client only has read access then you have to mount the volume with the ro option rather than the rw option.

   2. Make sure that you have told NFS to register any changes you made to /etc/exports since starting nfsd by running the exportfs command. Be sure to type exportfs -ra to be extra certain that the exports are being re-read.

   3. Check the file /proc/fs/nfs/exports and make sure the volume and client are listed correctly. (You can also look at the file /var/lib/nfs/xtab for an unabridged list of how all the active export options are set.) If they are not, then you have not re-exported properly. If they are listed, make sure the server recognizes your client as being the machine you think it is. For example, you may have an old listing for the client in /etc/hosts that is throwing off the server, or you may not have listed the client's complete address and it may be resolving to a machine in a different domain. One trick is login to the server from the client via ssh or telnet; if you then type who, one of the listings should be your login session and the name of your client machine as the server sees it. Try using this machine name in your /etc/exports entry. Finally, try to ping the client from the server, and try to ping the server from the client. If this doesn't work, or if there is packet loss, you may have lower-level network problems.

   4. It is not possible to export both a directory and its child (for example both /usr and /usr/local). You should export the parent directory with the necessary permissions, and all of its subdirectories can then be mounted with those same permissions.

2. RPC: Program Not Registered: (or another "RPC" error):

   This means that the client does not detect NFS running on the server. This could be for several reasons.

   1. First, check that NFS actually is running on the server by typing rpcinfo -p on the server. You should see something like this:

      program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100011 1 udp 749 rquotad 100011 2 udp 749 rquotad 100005 1 udp 759 mountd 100005 1 tcp 761 mountd 100005 2 udp 764 mountd 100005 2 tcp 766 mountd 100005 3 udp 769 mountd 100005 3 tcp 771 mountd 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 300019 1 tcp 830 amd 300019 1 udp 831 amd 100024 1 udp 944 status 100024 1 tcp 946 status 100021 1 udp 1042 nlockmgr 100021 3 udp 1042 nlockmgr 100021 4 udp 1042 nlockmgr 100021 1 tcp 1629 nlockmgr 100021 3 tcp 1629 nlockmgr 100021 4 tcp 1629 nlockmgr

      This says that we have NFS versions 2 and 3, rpc.statd version 1, network lock manager (the service name for rpc.lockd) versions 1, 3, and 4. There are also different service listings depending on whether NFS is travelling over TCP or UDP. UDP is usually (but not always) the default unless TCP is explicitly requested.

      If you do not see at least portmapper, nfs, and mountd, then you need to restart NFS. If you are not able to restart successfully, proceed to Symptom 9.

   2. Now check to make sure you can see it from the client. On the client, type rpcinfo -p server where server is the DNS name or IP address of your server.

      If you get a listing, then make sure that the type of mount you are trying to perform is supported. For example, if you are trying to mount using Version 3 NFS, make sure Version 3 is listed; if you are trying to mount using NFS over TCP, make sure that is registered. (Some non-Linux clients default to TCP). Type man rpcinfo for more details on how to read the output. If the type of mount you are trying to perform is not listed, try a different type of mount.

      If you get the error No Remote Programs Registered, then you need to check your /etc/hosts.allow and /etc/hosts.deny files on the server and make sure your client actually is allowed access. Again, if the entries appear correct, check /etc/hosts (or your DNS server) and make sure that the machine is listed correctly, and make sure you can ping the server from the client. Also check the error logs on the system for helpful messages: Authentication errors from bad /etc/hosts.allow entries will usually appear in /var/log/messages, but may appear somewhere else depending on how your system logs are set up. The man pages for syslog can help you figure out how your logs are set up. Finally, some older operating systems may behave badly when routes between the two machines are asymmetric. Try typing tracepath [server] from the client and see if the word "asymmetric" shows up anywhere in the output. If it does then this may be causing packet loss. However asymmetric routes are not usually a problem on recent linux distributions.

      If you get the error Remote system error - No route to host, but you can ping the server correctly, then you are the victim of an overzealous firewall. Check any firewalls that may be set up, either on the server or on any routers in between the client and the server. Look at the man pages for ipchains, netfilter, and ipfwadm, as well as the IPChains-HOWTO and the Firewall-HOWTO for help.

7.4. I do not have permission to access files on the mounted volume.

This could be one of two problems.

If it is a write permission problem, check the export options on the server by looking at /proc/fs/nfs/exports and make sure the filesystem is not exported read-only. If it is you will need to re-export it read/write (don't forget to run exportfs -ra after editing /etc/exports). Also, check /proc/mounts and make sure the volume is mounted read/write (although if it is mounted read-only you ought to get a more specific error message). If not then you need to re-mount with the rw option.

The second problem has to do with username mappings, and is different depending on whether you are trying to do this as root or as a non-root user.

If you are not root, then usernames may not be in sync on the client and the server. Type id [user] on both the client and the server and make sure they give the same UID number. If they don't then you are having problems with NIS, NIS+, rsync, or whatever system you use to sync usernames. Check group names to make sure that they match as well. Also, make sure you are not exporting with the all_squash option. If the user names match then the user has a more general permissions problem unrelated to NFS.

If you are root, then you are probably not exporting with the no_root_squash option; check /proc/fs/nfs/exports or /var/lib/nfs/xtab on the server and make sure the option is listed. In general, being able to write to the NFS server as root is a bad idea unless you have an urgent need -- which is why Linux NFS prevents it by default. See Section 6 for details.

If you have root squashing, you want to keep it, and you're only trying to get root to have the same permissions on the file that the user nobody should have, then remember that it is the server that determines which uid root gets mapped to. By default, the server uses the UID and GID of nobody in the /etc/passwd file, but this can also be overridden with the anonuid and anongid options in the /etc/exports file. Make sure that the client and the server agree about which UID nobody gets mapped to.

7.5. When I transfer really big files, NFS takes over all the CPU cycles on the server and it screeches to a halt.

This is a problem with the fsync() function in 2.2 kernels that causes all sync-to-disk requests to be cumulative, resulting in a write time that is quadratic in the file size. If you can, upgrading to a 2.4 kernel should solve the problem. Also, exporting with the no_wdelay option forces the program to use o_sync() instead, which may prove faster.

7.6. Strange error or log messages

1. Messages of the following format:

   Jan 7 09:15:29 server kernel: fh_verify: mail/guest permission failure, acc=4, error=13 Jan 7 09:23:51 server kernel: fh_verify: ekonomi/test permission failure, acc=4, error=13

   These happen when a NFS setattr operation is attempted on a file you don't have write access to. The messages are harmless.

2. The following messages frequently appear in the logs:

   kernel: nfs: server server.domain.name not responding, still trying kernel: nfs: task 10754 can't get a request slot kernel: nfs: server server.domain.name OK

   The "can't get a request slot" message means that the client-side RPC code has detected a lot of timeouts (perhaps due to network congestion, perhaps due to an overloaded server), and is throttling back the number of concurrent outstanding requests in an attempt to lighten the load. The cause of these messages is basically sluggish performance. See Section 5 for details.

3. After mounting, the following message appears on the client:

   nfs warning: mount version older than kernel

   It means what it says: You should upgrade your mount package and/or am-utils. (If for some reason upgrading is a problem, you may be able to get away with just recompiling them so that the newer kernel features are recognized at compile time).

4. Errors in startup/shutdown log for lockd

   You may see a message of the following kind in your boot log:

   nfslock: rpc.lockd startup failed

   They are harmless. Older versions of rpc.lockd needed to be started up manually, but newer versions are started automatically by nfsd. Many of the default startup scripts still try to start up lockd by hand, in case it is necessary. You can alter your startup scripts if you want the messages to go away.

5. The following message appears in the logs:

   kmem_create: forcing size word alignment - nfs_fh

   This results from the file handle being 16 bits instead of a mulitple of 32 bits, which makes the kernel grimace. It is harmless.

7.7. Real permissions don't match what's in /etc/exports.

/etc/exports is very sensitive to whitespace - so the following statements are not the same:

/export/dir hostname(rw,no_root_squash) /export/dir hostname (rw,no_root_squash)

The first will grant hostname rw access to /export/dir without squashing root privileges. The second will grant hostname rw privileges with root squash and it will grant everyone else read/write access, without squashing root privileges. Nice huh?

7.8. Flaky and unreliable behavior

Simple commands such as ls work, but anything that transfers a large amount of information causes the mount point to lock.

This could be one of two problems:

1. It will happen if you have ipchains on at the server and/or the client and you are not allowing fragmented packets through the chains. Allow fragments from the remote host and you'll be able to function again. See Section 6.4 for details on how to do this.

2. You may be using a larger rsize and wsize in your mount options than the server supports. Try reducing rsize and wsize to 1024 and seeing if the problem goes away. If it does, then increase them slowly to a more reasonable value.

7.9. nfsd won't start

Check the file /etc/exports and make sure root has read permission. Check the binaries and make sure they are executable. Make sure your kernel was compiled with NFS server support. You may need to reinstall your binaries if none of these ideas helps.

7.10. File Corruption When Using Multiple Clients

If a file has been modified within one second of its previous modification and left the same size, it will continue to generate the same inode number. Because of this, constant reads and writes to a file by multiple clients may cause file corruption. Fixing this bug requires changes deep within the filesystem layer, and therefore it is a 2.5 item.

8.1. AIX

8.2. BSD

8.3. Tru64 Unix

8.4. HP-UX

8.5. IRIX

8.6. Solaris

svc: unknown program 100227 (me 100003)
  

8.7. SunOS

SunOS only has NFS Version 2 over UDP.